Are Ethernet Cables Slowing Your Connection? (2024)

Look closely at your Ethernet cable to find its category number, which should be printed on the outer layer (sheath).

The category number tells you information about the cable’s design and its theoretical maximum (ceiling) speed over a set distance. The higher the number and the newer the design, the more data the cable transmits over a set distance.

For example, A CAT 3 cable is slow as snails and old as dirt. A CAT 8 cable is recent and comically faster than any home internet connection you can get right now.

Here’s a list of the speeds each category type can deliver:

As the chart shows, do not install a CAT 5 cable between your modem or fiber ONT and your router if your internet plan exceeds 100Mbps. Instead, use a CAT 5e or newer, at the very least, for anything above 101Mbps.

However, a CAT 6a cable or newer is ideal for Gig+ (1,001–1,999Mbps) and Multi-Gig (2,000+ Mbps) internet connections.

That said, you won’t see any speed changes if you use a short cable versus a long one if they’re both within the specification’s designated range. But all cables that extend beyond their specified range will see signal loss, which results in slower speeds. In other words, you’ll only get a 10Gbps connection out of a CAT 7 cable if it’s longer than 164 feet in length.

However, some may argue that shorter cables are better than long ones because data takes less time to reach its destination. After all, a car traveling at 50 MPH across 10 miles will reach its destination before a car traveling at the same speed across 100 miles.

With Ethernet, the time difference is in nanoseconds. Plus, electricity travels at 70% of the speed of light across a medium (copper in this case), so the argument is pointless. Length only becomes a speed issue if a cable is longer than the specification’s limit.

Still, you don’t want to use a 50-foot cable to connect your modem to your router if they’re sitting side-by-side—cable management would be a nightmare.

An Ethernet cable has two or four twisted copper wire pairs wrapped in foil and covered by a sturdy PVC sleeve. If the copper wires are damaged, you will have a slower connection—or no connection at all.

Keep in mind that cats and puppies love to chew on cables, and toddlers may pull on them just because they seem interesting and fun. Try to keep your cables out of reach from teeth, claws, and little fingers.

If you have Ethernet cables located outside, under your home, or in the attic, check them for damage, too. They’re just as susceptible to nature and human error as cable TV and telephone lines, so one little nick from a weed eater or a bite from a rodent can slow your connection to a crawl.

Why do some Ethernet cables use gold?

Some Ethernet cables use gold because it’s non-corrosive and more conductive, so keep that in mind when you shop for a new Ethernet cable.

Today’s mainstream electronics generally use five Ethernet port types: Fast Ethernet, Gigabit Ethernet, 2.5Gbps Ethernet, 5Gbps Ethernet, and 10Gbps Ethernet.

Gigabit Ethernet is the most common type of Ethernet port in desktops, laptops, game consoles, media streamers, routers, modems, and gateways. However, thanks to the rise of Gig+ and Multi-Gig internet, the 2.5Gbps Ethernet port is now more prominent on modems, gateways, and routers than in years past. We’ve seen only one use of a 5Gbps Ethernet port over the last several years, while 10Gbps Ethernet is common on fiber ONTs and gateways as well as new Wi-Fi 7 routers.

Now, here’s the thing. You’ll never see the port’s maximum speed due to network overhead, which is bandwidth used to carry information about the payload (your data) traveling down the line. We use 6% here to give you an idea of real-world speeds, although the percentage changes based on the protocol used to transfer your data—the percentage may be higher or lower.

And yes, it’s quite the rabbit hole. We get it. But Ethernet ports and cables play hand-in-hand. Plug a CAT 6 cable into a Gigabit Ethernet port, and chances are the most you get is 940Mbps—980Mbps if you’re lucky. Plug that same cable into a 2.5Gbps Ethernet port, and you still get around 940Mbps—the cable is now your only bottleneck. A CAT 6a cable and newer is best for Multi-Gig Ethernet ports.

If you have an older PC with a Fast Ethernet port, you can work around its limitation by purchasing a USB-to-Ethernet adapter that supports gigabit speeds. The older USB-A 2.0 port supports up to 480Mbps, which is better than a Fast Ethernet connection. However, you should use a USB-A 3.x or USB-C 3.x port, as they support 5,000Mbps (5Gbps) or 10,000Mbps (10Gbps), depending on the port’s configuration.

The bottom line here is to be wary about the Ethernet ports you have and how they affect your connections to other devices and the internet. Don’t expect to use a CAT 6a cable and get a 10 Gbps connection out of a Gigabit Ethernet port.

If you don’t know the maximum speed of your Ethernet port(s), we provide instructions on how to find a port’s speed on a Windows PC or a Mac in our FAQ.

What USB port do you have?

USB ports on PCs typically have two shapes. The “A” rectangular port is older and more common. Those that use the slower USB 2.0 standard are black and have the pitchfork-style symbol printed to the side. Those that use the 3.x standard are blue and have the SS pitchfork symbol printed to the side. The “C” port is smaller and more oval and supports 5 Gbps and higher speeds, depending on the technology installed behind it.

If you use Ethernet with a game console, PC, or streaming device, try moving the other end of your Ethernet cable to a different port on the router or gateway. There are usually four at the very least, and the one you’re using may be failing.

A bad Ethernet port will give you slow speeds or no connection at all. By switching ports, you can rule out other possibilities like internet problems, cable issues, and device issues. If your connection suddenly improves by using the new port, then something is wrong with the previous one. Put tape over the troublesome port, so you don’t use it again.

If you have a mesh kit that limits you to just one or two Ethernet ports, you may need to use Wi-Fi instead. Contact the manufacturer if you believe the Ethernet port is having technical issues.

Log in to your router or gateway’s interface, and make sure you didn’t accidentally block a wired device or limit its connection. The Ethernet cable and port may not be an issue at all, but rather a setting that’s preventing your device from seeing the connection’s full potential.

For example, routers and gateways provide Quality of Service settings that prioritize specific devices and traffic. You may run into speed issues if the router or gateway allocates more bandwidth to a gaming device and prioritizes its associated traffic.

If you have multiple Ethernet lines running through your home or office, chances are you may have an Ethernet switch box. They’re ideal if you ignore Wi-Fi altogether and wire everything that accesses the internet. They’re essentially little computers with only one job: forward data.

Like any computing device, switches need to be power cycled from time to time to clear up any hardware and software issues. If disconnecting and reconnecting the power doesn’t resolve your slowdown woes (and you’re sure the switch is the issue), then you may need to replace the unit.

Need a new Ethernet switch?

The best Ethernet switch you can get is the Linksys SE3008, but it supports gigabit speeds only. We also have picks for gamers and those who need power over Ethernet.

View on Amazon

Your Ethernet slowdown may result from a hardware or software issue requiring you to reboot your device.

Be sure that you keep your devices updated, too—install all operating system updates and drivers. An outdated network driver—software that allows the operating system to speak to the hardware—can cause connection problems, like slowdowns and disconnections. Manufacturers generally release new drivers throughout the year to improve performance and stamp out issues, so keeping them current is a must.

Cable modems, DSL modems, and many fiber optical network terminals (ONT) use Ethernet to deliver internet to a Wi-Fi router. If you replaced the Ethernet cable tethering the two devices and you still have speed issues that aren’t related to your internet connection, there may be problems with the Ethernet port on the modem or ONT. You may also be experiencing a general failure with the modem or ONT itself. Call your provider if you’ve ruled everything else out.

Some homes and offices may have Ethernet problems you just can’t fix. For example, many fiber-to-the-home and fiber-to-the-building services use Ethernet cables that are draped behind walls and connected to Ethernet wall jacks. There may be an issue with the cable or the wall-mounted port that requires a technician to fix.